Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
We've noticed this article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the net and reckoned it made sense to relate it with you on this site.
Installing a bath tub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old bathtub is conveniently accessible, the task can relocate easily; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need a helper to move out the old tub and set in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub as well as don't need to transform the plan of your previous supply of water pipes.
Your devices as well as material checklist need to consist of the following:
Preparing for the Installment
First of all, the supporting structure provided with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four little points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the spirit level reads level.
To install taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the water and also inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been made use of at least when as this will resolve it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, triggering the water to pass through the wall in between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can fracture fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt on A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for finding the time to browse our article post. Enjoyed reading our article? Please share it. Help others discover it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Check This Out
Report this page